Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Blog Article
This post in the next paragraphs on the subject of How to Install a Bathtub is highly engaging. Read on and make your own personal ideas.
Setting up a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bath tub with a new one is likewise a moderately tough task. If the old tub is conveniently accessible, the job can relocate rapidly; if you need to open a wall to get rid of the old tub and also position the new bath tub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will require an assistant to move out the old bathtub and also set in the brand-new one. See to it you have qualified yourself for the work and also are comfortable attempting it. As opposed to hiring a professional to take control of a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you might require an expert plumber to make tube links.
This short article will certainly aid you install a new tub in your bathroom if you have currently acquired a new tub and also don't need to transform the arrangement of your previous water system pipelines.
Your devices and material checklist need to comprise the following:
Preparing for the Setup
To start with, the supporting frame supplied with the bath ought to be fitted (if needed) according to the supplier's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent strain on the tub.
Fit the versatile faucet adapters to the bottom of both faucets using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its final position.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, activate the faucets to drain any water continuing to be in the system. The process of removing the existing taps can be fairly bothersome because of the restricted access that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning throughout this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the brand-new taps, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Setting up the Bathtub
Making use of the two wooden boards under its feet, put the bathtub in the needed position. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 little factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the tub till the spirit level checks out level.
To set up taps, fit all-time low of the furthest versatile faucet port to the ideal supply pipe by making a compression sign up with; then do the very same for the other tap.
Activate the supply of water and also check all joints and also new pipework for leakages and also tighten them if necessary. Fill up the bathtub and likewise check the overflow outlet as well as the normal outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bath tub should wait up until the bath tub has been used a minimum of when as this will settle it right into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin making certain that the washers are in place between the tap as well as the sink. Safeguard the faucet in position with the manufacturer offered backnut. Once the tap is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet ports. The previous kind needs to be attached to the faucet ends first, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, causing issues with moisture as well as possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked newspaper or soft rope. Remember to constantly fill up the tub with water before securing, to enable the movement experienced when the tub remains in use. The sealant can crack rather very early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily available on the marketplace. It is a good idea to fit the tiles making use of waterproof or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading up on How to Install a Bathtub Yourself? Try leaving feedback down below. We'd be delighted to find out your thinking about this article. Hoping that you visit us again in the future. Liked our post? Please share it. Help others check it out. I am grateful for your time. Don't forget to come by our website back soon.
Visit The Following Page
Report this page